Buttons have a wide range of applications, especially the usual ones. Some of the Clothes we wear, when we see so many beautiful buttons, many people want to know how the buttons are made in the end. Here are the tips of the small button makers. The process of making a button and some related precautions.
1) The surface shape of the button, in the shape of the button, most of them are hand-grinding styling knives. The disadvantage is the same shape, the same model, when the number is large, the shape easily run away, which depends on the responsibility of the buckle technician Responsible and qualified technicians can do a good job. Then there is a sharpening machine. If the number is large, it will be very good and it will not run. However, when setting up the knife, it is also necessary to pay attention to the distance between the surface and the left and right sides. The tool holder is not very delicate and has clearance.
2) The thickness of the edge of the button, the edge of a button is not noticed, the same batch of goods are thick and thin, there is no unified, this is related to the responsibility of the deduction machine chuck and technician, when the chuck adjustment Generally, I saw the buckle technicians in the deduction factory. After adjusting the outside of the machine, after installing the machine, most of them did not adjust. In fact, although the collet has been adjusted, after the machine is installed, it still needs to be adjusted. Since -1) Did you have the greasy and dusty dust on the cartridge when you installed it? 2) Isn't there any error in the part of your machine's chuck?
3) What part of the machine's chuck is installed? Is there any dirt in it? Therefore, even if the clip is installed, you still need to be responsible for the thickness of each button. Adjustments are still needed. In order to ensure the uniform thickness of the button. When the button is installed, the unit is OK and the button is adjusted (thickness, edge, shape, eye distance). When you start production, please put a few OKs next to the button machine, because these buttons are It is often the case that large goods are produced at a later time. When starting to produce large goods, these buttons are used to come to an end. When deductions are made, buttons are often used to see the buttons. When using common calipers, the quantity is used for comparison. The quality of a batch of buttons.
4) The tool used to make the deduction, that depends on the responsibility of the deduction technician, the general deduction technician more lazy sharpening knife, it seems not their own, and it is too late, it really can not stand it, grinding it, hey, now How many people like this, ah, buckle technicians to look at the buttons in the system, found that the tool is blunt, immediately sharpen the knife, the button to do too hair, then affect the overall quality of buttons, and beautiful, and may become obsolete. There are also requirements for the scraping of the buttons, and the low scraping should also be controlled. Do not scratch it. The low arc must follow suit.
During the deduction process, we must look more, use more calipers, compare the appearance of the calipers, and find that the problem is immediately resolved. Do not wait until the button reaches the finished product. Only after the problem is discovered, what is late? , wasting manpower, financial resources, and delivery date.
Characteristics of copper clad aluminum buckle and anti-corrosion treatment 1. Copper clad aluminum buckle characteristics and quality indicators Copper clad aluminum buckle due to the use of H62 brass surface material, its color is similar to 18K gold color, so there is a strong decorative , And after an excellent surface treatment method, it can ensure long-term use without discoloration and rust. In addition, the copper surface of the copper clad aluminum buckle is very thin, with very little copper. At the same time, the clasp of the copper clad aluminum buckle is made of aluminum alloy, which ensures the mechanical strength of the buttons. The absolute strength of the buckle handle can reach more than 300N, so that the copper buckle aluminum buckle can be used under any conditions without losing the buckle phenomenon.
2. Anti-corrosion treatment of copper clad aluminum buckle The basic method of anti-corrosion of copper is to make the surface of H62 brass appear to have a brightness of approximately 18K gold by means of micro acid polishing. The protective film is then immersed or sprayed on the surface with a repeated coating method. The bottom layer of the impregnated paint is a paint type with good sealing performance to improve its protective performance; the sprayed part requires the use of a paint with high hardness to increase the abrasion resistance of the paint film and prolong its use time, so as to ensure the long-term use of the button. Will change color and rust.
Timber buttons and bamboo buttons belong to the buttons of plant stems. In the international market, there are a lot of such buttons. In particular, in recent years, as people have pursued the greening of environmental quality, the demand for such plant buttons has increased, and consumption in developed countries such as Europe, America and Japan has gradually increased. The product structure is dominated by wood buttons. The motivation for people to choose wood buttons first stems from the tedious psychology of long-term use of synthetic plastics. Many people believe that "natural" materials must be non-toxic and beneficial to human health, and wood buttons cater to people's psychology.
The wood button has a natural wood texture, which is very simple and natural, and its appearance is rough, which contrasts sharply with the high gloss of plastic buttons.
Therefore, these buttons are compatible with hemp fabrics or plain casual wear, and at the same time, they can satisfy some of the people with their unconventional and unconventional aesthetic habits. The main component of the wood button is lignin, which is highly resistant to organic solvents, durable dry cleaning agent, and can be dry cleaned together with clothing. The deadly disadvantage of timber buttons is its water absorption. Because of the strong water absorption of wood fiber, once it is wet, or when it is thrown into water, it will quickly absorb water, expand, and when it is dry, it may crack, deform, or become rough, and it is easy to hook clothing. fiber. In order to overcome the shortcomings of timber buttons, the selection of materials should pay attention to choose wood dense, long growing period, old trees or parts. After the buttons are polished, the surface is treated with a high-quality varnish and all water-absorbing pores are sealed. Buttons that have been treated in this way can prevent water absorption problems.
For more information, please update: China Button Industry Network
Household Commodities,Household Commodities price,Household Commodities quality,Household Goods Stand
Nanjing Intime Import and Export co., Ltd. , https://www.njireneintime.com